Super simple chassis connections - no OEM fuseboxes needed. Ignition, Fuel Pump & Gauges - a handful of labeled wires for you to connect.
Fully finished harness - all loom secured and engine / transmission connectors attached.
Key Features Include:
- Integrated Coil Pack Harnesses - both banks now provided for no extra charge
- Standalone 5 Circuit Bussmann Fuse/Relay Block provided - no connections to OEM fuse boxes needed
- Circuits provided: Ignition, Fuel Pump, Fan1, Fan2 & A/C relay (if not using A/C can be used for aux function like oil or diff cooler fan etc)
- Proper gauge wiring support for Dual 30 Amp PCM-controlled electric cooling fans
- ThermaShield 1,2200F Aluminum / Fiberglass Connector protection provided on knock sensors - no more melted knock sensor connectors
The 6L80/6L90 Auto Trans CAN Option Supports:
- A/C Request
- Tap Up/ Tap Down
- Tow/ Haul Mode
- Park/ Neutral Starter Relay Safety
- Reverse Lights Relay Output
- CAN -> Speedometer Output
- CAN -> Tachometer Output
SUPPORTED ENGINES: GM 6.0 LITER LY6/L96 ENGINES USING DRIVE BY WIRE / ELECTRONIC THROTTLE
- 2007-2009 Chevrolet Silverado 2500HD, 3500HD (LY6 Vortec)
- 2007-2009 GMC Sierra 2500HD, 3500HD (LY6 Vortec)
- 2007-2009 Chevrolet Suburban 3/4 ton (LY6 Vortec)
- 2007-2009 GMC Yukon XL 3/4 ton (LY6 Vortec)
- 2008-2009 Chevrolet Express 2500HD, 3500HD (LY6 Vortec)
- 2008-2009 GMC Savana 2500HD, 3500HD (LY6 Vortec)
- 2010-present Chevrolet Silverado HD (L96 Vortec)
- 2010-present GMC Sierra HD (L96 Vortec)
- 2010-2013 Chevrolet Suburban 3/4 ton (L96 Vortec)
- 2010-2013 GMC Yukon XL 3/4 ton (L96 Vortec)
- 2016-present Chevrolet Suburban 3500 (L96 Vortec)
- 2016-present Chevrolet Express/GMC Savana (L96 Vortec)
PRO-SERIES HARNESS TECHNICAL SPECS
- Plug and Play – simple and efficient
- NO CORE HARNESS or additional wiring required
- OEM wire colors used, where applicable
- All sensor signal connection use EM shielded wires
- Super-High Temp Fireproof fiberglass loom used on knock sensor, O2 sensor & transmission branches located in hot areas. (-40°C/-40°F to +450°C/+845°F operating temperature)
- Point-to-Point continuity tested on every wire
- Constructed using exact OEM connectors and seals
- Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature)
- Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature)
- Includes a charge harness and improved grounds
- Fully tested after production for an easy plug-and-play installation
PRO-SERIES HARNESS INCLUDES
- Harness fully redesigned with optimized & improved power and ground routing
- Supplied with 5 Fused Relays in a weather-tight sealed Bussmann Box
- Relays provided: Ignition, Fuel Pump, Fan1, Fan2 & A/C relay (if not using A/C can be used for aux function like oil/diff cooler fan etc)
- Main Engine and Transmission one-piece tucked harness
- Alternator charge cable built into the main harness
- Knock sensor sub-harness connector
- MAFS connector
- MAP sensor connector
- Intake Air Temp connector
- TPS connector
- 8x Injector connectors
- Integrated Bank 1 and Bank 2 Coil Harnesses in the OEM location – no sub-harnesses required
- Oil Pressure gauge connector
- Proper gauge wiring support for Dual 30 Amp PCM-controlled electric cooling fans
- Cam sensor connector
- Crank sensor connector
- Bank 1 and Bank 2 FRONT Oxygen sensor connectors (High Temp shielding)
- 1 x Ground ring terminal
- Idle air connector
- ECT sensor connector and cluster coolant temp switch connector
- Reverse lights sensor connector
- Speed sensor connector
- Reverse Lockout connector
- Skip Shift connector
- Alternator connector
- Starter signal/start connector
- A/C Wiring is available as an option. Please note that adding A/C to an LS2 is not easy and will require custom lines and sensor installation. Wiring Specialties will provide a wiring sub-harness needed for operating the A/C system ONLY
- OBD2 Communication connector
- Printable install instructions with pictures
- Turn Key ENGINE START Guarantee
- Tech support for our customers 7 days a week
FAQ & OTHER DETAILS
- Startup PCM Flash Tune - GM LS3 PCMs require basic tuning in order to run the LS engine in a different chassis. The VATS alarm or Immobilizer will prevent the engine from starting unless it is disabled. The standard base startup tune is VATS / EVAP / Rear O2 / Fuel Tank Purge removal. Most tunes leave the other parameters stock. No performance settings are changed with this startup tune - fuel map changes are NOT part of this service. Please feel free to contact us with any questions regarding this service.
- Alternator Charge Cable - This item ties the starter/battery directly to the Alternator output, which allows the improved power routing on our harness to eliminate the wire running from the alternator to the fusebox and/or battery while still charging the battery normally.
- Grounding Kit - Our Kit ties a number if engine components to the body of the car and ensures that you will not have issues resulting from poor grounds. The Grounding Kit utilizes Ultra High temp fiberglass sleeving to allow installation under or around exhaust components. Very flexible mounting options allow you to connect the block, head, battery tray, alternator case and chassis to completely eliminate all grounding issues.
- Speedo Signal Conditioning - The Dakota Digital SGI-5 unit for Speed can 'condition' the signal to compensate for cross-platform swaps. If the Option exists to ADD the unit on the harness page for your swap, then you need it for proper speedo operation. Please note that some transmissions (350z, BMW ZF and S15 Silvia for example) do not have a speed sensor and will require a non-harness based solution like a GPS speedo.
- Plug-n-Play vs Universal - Plug-n-Play harnesses connect to your car's underhood fuse box for power and to connectors under the dash for gauges etc. Universal harnesses do not need an underhood fusebox to connect to and the wiring for gauges and warning lights is provided as a 'flying lead' which are bare wires labeled with their function.
- Right Hand Drive (RHD) Conversions - If you used ALL the stock LHD chassis connectors for your RHD swap, order the LHD version of the harness. If you used ALL the clip/swap RHD chassis connectors, order the RHD version of the harness. If you used a combination of LHD and RHD chassis connectors, please contact us as our harnesses will need modification.
- Don't See It? - If you have injectors, throttle body, coilpacks or any other item that you do not see on the Options offerings, please contact us. Chances are we can do it!
- Battery Cables / Battery Relocation - The battery must be connected to the starter, so you need a battery cable from the positive battery terminal to the starter main power lug. Typically this positive battery cable also powers up the main under hood fusebox, which runs many of the non-engine items on your car like interior lights, dash power and headlights/taillights. Please make sure you have prepared for this as each install is different.